# quick quesion about the dark magic 2 **URL:** \ **Category:** Yo-Yo Mods and Maintenance\ **Created:** [February 14, 2012, 9:07pm UTC](https://forums.yoyoexpert.com/t/quick-quesion-about-the-dark-magic-2/34887 "2012-02-14T21:07:58Z")\ **Posts on this page:** 7\ **Page:** 1
**Author:** ![Tgoodyoyo](https://avatars.discourse-cdn.com/v4/letter/t/8baadc/32.png) [@Tgoodyoyo](https://forums.yoyoexpert.com/u/Tgoodyoyo)\ **Post date:** [February 14, 2012, 9:07pm UTC](https://forums.yoyoexpert.com/t/quick-quesion-about-the-dark-magic-2/34887/1 "2012-02-14T21:07:58Z")
on the unresponsive bearing are there 2 c-clips because i can only get 1 off ---
**Author:** ![skitrz](https://sea1.discourse-cdn.com/flex015/user_avatar/forums.yoyoexpert.com/skitrz/32/849_2.png) [@skitrz](https://forums.yoyoexpert.com/u/skitrz)\ **Post date:** [February 14, 2012, 9:11pm UTC](https://forums.yoyoexpert.com/t/quick-quesion-about-the-dark-magic-2/34887/2 "2012-02-14T21:11:50Z")
Yes, bearings have two, one on each side to hold the shields on. Sometimes it can be difficult to see the gap in the clip, try better lighting or a magnifying glass. You can often find the gap by running the end of the needle around the edge. You can feel the end of the needle drop into the gap. ---
**Author:** ![anonyo](https://avatars.discourse-cdn.com/v4/letter/a/8baadc/32.png) [@anonyo](https://forums.yoyoexpert.com/u/anonyo)\ **Post date:** [February 14, 2012, 9:12pm UTC](https://forums.yoyoexpert.com/t/quick-quesion-about-the-dark-magic-2/34887/3 "2012-02-14T21:12:51Z")
> [@Tgoodyoyo](#): > > on the unresponsive bearing are there 2 c-clips because i can only get 1 off 1 on each side. It may be hard to see. Be under a bright desk light and prepare to look at very many angles until you see the gap, then use a needle to try to get it out. Of one end is hard to get, try the other end, it may work better. The clips are very thin and narrow. This isn’t an unusual problem. Just keep trying. ---
**Author:** ![Tgoodyoyo](https://avatars.discourse-cdn.com/v4/letter/t/8baadc/32.png) [@Tgoodyoyo](https://forums.yoyoexpert.com/u/Tgoodyoyo)\ **Post date:** [February 14, 2012, 9:19pm UTC](https://forums.yoyoexpert.com/t/quick-quesion-about-the-dark-magic-2/34887/4 "2012-02-14T21:19:12Z")
okay thanks guys ---
**Author:** ![jhb8426](https://sea1.discourse-cdn.com/flex015/user_avatar/forums.yoyoexpert.com/jhb8426/32/631_2.png) [@jhb8426](https://forums.yoyoexpert.com/u/jhb8426)\ **Post date:** [February 14, 2012, 9:42pm UTC](https://forums.yoyoexpert.com/t/quick-quesion-about-the-dark-magic-2/34887/5 "2012-02-14T21:42:47Z")
In addition to what was said, you really only need to take one off for cleaning. The only reason to pull both is if you don’t want them on at all. ---
**Author:** ![anonyo](https://avatars.discourse-cdn.com/v4/letter/a/8baadc/32.png) [@anonyo](https://forums.yoyoexpert.com/u/anonyo)\ **Post date:** [February 14, 2012, 11:23pm UTC](https://forums.yoyoexpert.com/t/quick-quesion-about-the-dark-magic-2/34887/6 "2012-02-14T23:23:53Z")
> [@jhb8426](#): > > In addition to what was said, you really only need to take one off for cleaning. The only reason to pull both is if you don’t want them on at all. I’m going to respectfully disagree. Especially when you’re spinning and blowing out the bearing to dry it, you want to make sure that whatever it is you’re cleaning out has someplace to go OUTSIDE of the bearing. Even in the solvents, it helps when you’re taking the bearing out for the fluid to be able to just freely take the stuff out. So, I recommend removing both bearing shields for cleaning. That’s how I see it. ---
**Author:** ![fellavader](https://sea1.discourse-cdn.com/flex015/user_avatar/forums.yoyoexpert.com/fellavader/32/905_2.png) [@fellavader](https://forums.yoyoexpert.com/u/fellavader)\ **Post date:** [February 20, 2012, 4:43pm UTC](https://forums.yoyoexpert.com/t/quick-quesion-about-the-dark-magic-2/34887/7 "2012-02-20T16:43:15Z")
I agree with studio you should take off both shields. You will get better results. Just an FYI on the center track bearings to take off the C clip I use the needle to push on the right side of the opening but for all other bearing I push the pin into the left part of the C clip.