# Pads for Duncan Metal Drifter **URL:** \ **Category:** Yo-Yo Mods and Maintenance\ **Created:** [December 10, 2012, 2:14am UTC](https://forums.yoyoexpert.com/t/pads-for-duncan-metal-drifter/46388 "2012-12-10T02:14:22Z")\ **Posts on this page:** 14\ **Page:** 1
**Author:** ![chriscollins14](https://sea1.discourse-cdn.com/flex015/user_avatar/forums.yoyoexpert.com/chriscollins14/32/1026_2.png) [@chriscollins14](https://forums.yoyoexpert.com/u/chriscollins14)\ **Post date:** [December 10, 2012, 2:14am UTC](https://forums.yoyoexpert.com/t/pads-for-duncan-metal-drifter/46388/1 "2012-12-10T02:14:22Z")
So I recently decided to buy a Meal Drifter to screw around with but it’s super responsive. I cleaned out the bearing and taken one pad off and it’s helped a little but it’s still a little to responsive. Any other types of pads to help? Any other suggestions as to how I can make it even less responsive? ---
**Author:** ![YoCorey](https://avatars.discourse-cdn.com/v4/letter/y/0ea827/32.png) [@YoCorey](https://forums.yoyoexpert.com/u/YoCorey)\ **Post date:** [December 10, 2012, 2:17am UTC](https://forums.yoyoexpert.com/t/pads-for-duncan-metal-drifter/46388/2 "2012-12-10T02:17:04Z")
take out the remaining pad and silicone it and then add a better bearing. ---
**Author:** ![chriscollins14](https://sea1.discourse-cdn.com/flex015/user_avatar/forums.yoyoexpert.com/chriscollins14/32/1026_2.png) [@chriscollins14](https://forums.yoyoexpert.com/u/chriscollins14)\ **Post date:** [December 10, 2012, 2:27am UTC](https://forums.yoyoexpert.com/t/pads-for-duncan-metal-drifter/46388/3 "2012-12-10T02:27:29Z")
> [@YoCorey](#): > > take out the remaining pad and silicone it and then add a better bearing. How do I silicone it without a deep enough groove to put it in… ---
**Author:** ![Jerrod](https://sea1.discourse-cdn.com/flex015/user_avatar/forums.yoyoexpert.com/jerrod/32/367145_2.png) [@Jerrod](https://forums.yoyoexpert.com/u/Jerrod)\ **Post date:** [December 10, 2012, 2:38am UTC](https://forums.yoyoexpert.com/t/pads-for-duncan-metal-drifter/46388/4 "2012-12-10T02:38:59Z")
😃 ---
**Author:** ![chriscollins14](https://sea1.discourse-cdn.com/flex015/user_avatar/forums.yoyoexpert.com/chriscollins14/32/1026_2.png) [@chriscollins14](https://forums.yoyoexpert.com/u/chriscollins14)\ **Post date:** [December 10, 2012, 3:04am UTC](https://forums.yoyoexpert.com/t/pads-for-duncan-metal-drifter/46388/5 "2012-12-10T03:04:39Z")
> [@Jerrod](#): > > Make sure the bearing is clean and working properly. If you add thin lube, just use a very tiny “pin drop” amount. The pad will wear down over time from play, making it more unresponsive. You can always practice responsive play until your pad develops the “sweet spot.” I mean I don’t want to spend much time breaking it in when I can just throw my Ava or C3 Capless. ---
**Author:** ![Jerrod](https://sea1.discourse-cdn.com/flex015/user_avatar/forums.yoyoexpert.com/jerrod/32/367145_2.png) [@Jerrod](https://forums.yoyoexpert.com/u/Jerrod)\ **Post date:** [December 10, 2012, 3:09am UTC](https://forums.yoyoexpert.com/t/pads-for-duncan-metal-drifter/46388/6 "2012-12-10T03:09:51Z")
😃 ---
**Author:** ![anonyo](https://avatars.discourse-cdn.com/v4/letter/a/8baadc/32.png) [@anonyo](https://forums.yoyoexpert.com/u/anonyo)\ **Post date:** [December 10, 2012, 5:09am UTC](https://forums.yoyoexpert.com/t/pads-for-duncan-metal-drifter/46388/7 "2012-12-10T05:09:03Z")
> [@chriscollins14](#): > > > [@YoCorey](#): > > > > take out the remaining pad and silicone it and then add a better bearing. > > How do I silicone it without a deep enough groove to put it in… Don’t. Use Duncan Silicone stickers. If you silicone it, it’s gonna rip out rather fast. So, don’t do this. ---
**Author:** ![carl311](https://avatars.discourse-cdn.com/v4/letter/c/49beb7/32.png) [@carl311](https://forums.yoyoexpert.com/u/carl311)\ **Post date:** [December 10, 2012, 8:06pm UTC](https://forums.yoyoexpert.com/t/pads-for-duncan-metal-drifter/46388/8 "2012-12-10T20:06:10Z")
Total thread jack, but in a good way (I hope). As far as pads go, has anyone used thin .555 pads in the Metal Drifter with any luck? Better than the stock Duncan silicone ones? Also, I’ve read that putting thicker shims in the MD to widen the gap helps. I dont have any, but I was gonna dig around in my toolbox for some thin washers to put behind the stock shims… ---
**Author:** ![anonyo](https://avatars.discourse-cdn.com/v4/letter/a/8baadc/32.png) [@anonyo](https://forums.yoyoexpert.com/u/anonyo)\ **Post date:** [December 10, 2012, 8:12pm UTC](https://forums.yoyoexpert.com/t/pads-for-duncan-metal-drifter/46388/9 "2012-12-10T20:12:29Z")
> [@carl311](#): > > Total thread jack, but in a good way (I hope). As far as pads go, has anyone used thin .555 pads in the Metal Drifter with any luck? Better than the stock Duncan silicone ones? > > Also, I’ve read that putting thicker shims in the MD to widen the gap helps. I dont have any, but I was gonna dig around in my toolbox for some thin washers to put behind the stock shims… This isn’t a thread jack. If they make .555 pads for an A-bearing yoyo, that might be a viable option. However, I am not aware if they do or not, so I cannot answer your idea with a qualified answer. Since the Metal Drifter uses an A-sized bearing that’s part of the issue. There are two versions of the Metal Drifter that I am aware of, and I am aware of this because I have the older one with spacers, while my son has the 2012 version that does not use spacers. For his, I simply cleaned his bearing out and it went dead unresponsive. I did not touch the silicone response stickers. As far as mine, I need to re-clean the bearing, as my bearing cleaning technique has changed and that may be all I need to do to get satisfactory results. I’m going to be cleaning a batch of A bearings today from various Duncans. ---
**Author:** ![MetalMilitia](https://sea1.discourse-cdn.com/flex015/user_avatar/forums.yoyoexpert.com/metalmilitia/32/183_2.png) [@MetalMilitia](https://forums.yoyoexpert.com/u/MetalMilitia)\ **Post date:** [December 10, 2012, 8:41pm UTC](https://forums.yoyoexpert.com/t/pads-for-duncan-metal-drifter/46388/10 "2012-12-10T20:41:57Z")
I don’t know if they’re still available anywhere, but I used to use Gen-pads with success in my Freehands. They worked very well matched up with a dead friction sticker. See if you can get a hold of some. ---
**Author:** ![jhb8426](https://sea1.discourse-cdn.com/flex015/user_avatar/forums.yoyoexpert.com/jhb8426/32/631_2.png) [@jhb8426](https://forums.yoyoexpert.com/u/jhb8426)\ **Post date:** [December 11, 2012, 1:58am UTC](https://forums.yoyoexpert.com/t/pads-for-duncan-metal-drifter/46388/11 "2012-12-11T01:58:57Z")
> [@YoCorey](#): > > take out the remaining pad and silicone it and then add a better bearing. Probably just cleaning the bearing is sufficient. 95% of a yoyo’s response is in the bearing condition. No need for a new bearing. Definitely don’t silicone it. get sili pads as Studio42 suggests. ---
**Author:** ![Joeybob](https://avatars.discourse-cdn.com/v4/letter/j/ecc23a/32.png) [@Joeybob](https://forums.yoyoexpert.com/u/Joeybob)\ **Post date:** [December 11, 2012, 4:39am UTC](https://forums.yoyoexpert.com/t/pads-for-duncan-metal-drifter/46388/12 "2012-12-11T04:39:18Z")
Dif pads or duncan 13.7 mm silicone stickers+ a clean long spinning bearing and it is good to go. ---
**Author:** ![Bcmaddog](https://sea1.discourse-cdn.com/flex015/user_avatar/forums.yoyoexpert.com/bcmaddog/32/1170_2.png) [@Bcmaddog](https://forums.yoyoexpert.com/u/Bcmaddog)\ **Post date:** [December 11, 2012, 7:57pm UTC](https://forums.yoyoexpert.com/t/pads-for-duncan-metal-drifter/46388/13 "2012-12-11T19:57:51Z")
> [@chriscollins14](#): > > > [@YoCorey](#): > > > > take out the remaining pad and silicone it and then add a better bearing. > > How do I silicone it without a deep enough groove to put it in… its possible if you use flowable put in a little and let it flow! 😃 ---
**Author:** ![Bcmaddog](https://sea1.discourse-cdn.com/flex015/user_avatar/forums.yoyoexpert.com/bcmaddog/32/1170_2.png) [@Bcmaddog](https://forums.yoyoexpert.com/u/Bcmaddog)\ **Post date:** [December 11, 2012, 7:58pm UTC](https://forums.yoyoexpert.com/t/pads-for-duncan-metal-drifter/46388/14 "2012-12-11T19:58:53Z")
EDIT. Use Duncan sillicone as studio mentioned, I forgot what it was called :wink: