# Bearing removal tools
**URL:** https://forums.yoyoexpert.com/t/bearing-removal-tools/364367
**Category:** Yo-Yo Mods and Maintenance
**Created:** [October 15, 2022, 8:15pm UTC](https://forums.yoyoexpert.com/t/bearing-removal-tools/364367 "2022-10-15T20:15:29Z")
**Posts on this page:** 8
**Page:** 1
### Author:  [@Hojo-YoYo](https://forums.yoyoexpert.com/u/Hojo-YoYo)
#### Post date: [October 15, 2022, 8:15pm UTC](https://forums.yoyoexpert.com/t/bearing-removal-tools/364367/1 "2022-10-15T20:15:29Z")
Other than the standard removal tool that you get with some throws or buy as an accessory, what else do you use?
I found in one of my tool boxes in the garage an old spark plug boot remover. It is rubber coated so no scratches and it seems to work well.
---
### Author:  [@nappyrat](https://forums.yoyoexpert.com/u/nappyrat)
#### Post date: [October 15, 2022, 8:22pm UTC](https://forums.yoyoexpert.com/t/bearing-removal-tools/364367/2 "2022-10-15T20:22:50Z")
i wrap a rubber band around the bearing and use needle nose pliers to get in the center trac groove. i pull straight out and avoid wiggling the prevent wearing down the bearing seat post
---
### Author:  [@Hojo-YoYo](https://forums.yoyoexpert.com/u/Hojo-YoYo)
#### Post date: [October 15, 2022, 8:33pm UTC](https://forums.yoyoexpert.com/t/bearing-removal-tools/364367/3 "2022-10-15T20:33:49Z")
That was the idea behind using this. I never like the the tool that went inside the bearing and then had to rock it back and forth to get it off. I can pull it straight off with this.
---
### Author:  [@Lefski](https://forums.yoyoexpert.com/u/Lefski)
#### Post date: [October 15, 2022, 10:21pm UTC](https://forums.yoyoexpert.com/t/bearing-removal-tools/364367/4 "2022-10-15T22:21:21Z")
Most of my throws have very precisely machined bearing posts, so i can easily remove the bearing with my bare hands. Only 2 of them need a little more encouragement. I use a simple, old fashioned wooden clothespin to convince them.
---
### Author:  [@adamantiumpops](https://forums.yoyoexpert.com/u/adamantiumpops)
#### Post date: [October 16, 2022, 3:01pm UTC](https://forums.yoyoexpert.com/t/bearing-removal-tools/364367/5 "2022-10-16T15:01:29Z")
My two Leatherman multitools have painter’s tape around their jaws if I ever need to use them to remove a bearing. Otherwise the little tube tools work just fine.
---
### Author:  [@craZivn](https://forums.yoyoexpert.com/u/craZivn)
#### Post date: [October 16, 2022, 6:55pm UTC](https://forums.yoyoexpert.com/t/bearing-removal-tools/364367/6 "2022-10-16T18:55:54Z")
I wonder about pulling the bearing off by the outside as opposed to the inside. If the bearing post is tight, isn’t there a risk of damaging the bearing by side-loading it? It seems like on some yoyos with tighter posts, it would be a lot of stress through the components of the tiny bearing.
Or am I over-thinking this?
Ivan
---
### Author:  [@tropical\_vibes](https://forums.yoyoexpert.com/u/tropical_vibes)
#### Post date: [October 17, 2022, 3:25am UTC](https://forums.yoyoexpert.com/t/bearing-removal-tools/364367/7 "2022-10-17T03:25:50Z")
I’ll have to give the rubber band idea a go. That sounds like the best across the board —for protection, grip and being able to take it out without rocking.
Thus far have added a layer of protection in the form of an old T-shirt and used needle nose pliers. It works but I don’t like it. Slips too much.
---
### Author:  [@jhb8426](https://forums.yoyoexpert.com/u/jhb8426)
#### Post date: [October 17, 2022, 4:09am UTC](https://forums.yoyoexpert.com/t/bearing-removal-tools/364367/8 "2022-10-17T04:09:15Z")
I still favor using a drill bit that fits in the center, or a brass/steel tube of the appropriate size if the bearing is on the axle side. My alternative is a pliers with masking tape on the jaws. If you’re gentle enough, just a bare pliers works just fine.