# Bearing measurements

**URL:** <https://forums.yoyoexpert.com/t/bearing-measurements/336836>\
**Category:** General Yo-Yo\
**Created:** [April 7, 2021, 5:07pm UTC](https://forums.yoyoexpert.com/t/bearing-measurements/336836 "2021-04-07T17:07:11Z")\
**Posts on this page:** 14\
**Page:** 1

<div class="post-metadata">

**Author:** ![zslane](https://sea1.discourse-cdn.com/flex015/user_avatar/forums.yoyoexpert.com/zslane/32/19816_2.png) [@zslane](https://forums.yoyoexpert.com/u/zslane)\
**Post date:** [April 7, 2021, 5:07pm UTC](https://forums.yoyoexpert.com/t/bearing-measurements/336836/1 "2021-04-07T17:07:11Z")

</div>

So when a C spec bearing is listed as having measurements of 0.250 x 0.500 x 0.187, what is each of those three numbers referring to?

---

<div class="post-metadata">

**Author:** ![Isaac](https://sea1.discourse-cdn.com/flex015/user_avatar/forums.yoyoexpert.com/isaac/32/597931_2.png) [@Isaac](https://forums.yoyoexpert.com/u/Isaac)\
**Post date:** [April 7, 2021, 5:09pm UTC](https://forums.yoyoexpert.com/t/bearing-measurements/336836/2 "2021-04-07T17:09:52Z")

</div>

I assume some combo of inner diameter, outer diameter, and width of the bearing (like how d-bearings coming in 4mm and 5(?)mm versions). In the size C specs you listed, I’m guessing it goes:

.250in Inner Diameter  
.500in Outer Diameter  
.187in Width

---

<div class="post-metadata">

**Author:** ![zslane](https://sea1.discourse-cdn.com/flex015/user_avatar/forums.yoyoexpert.com/zslane/32/19816_2.png) [@zslane](https://forums.yoyoexpert.com/u/zslane)\
**Post date:** [April 7, 2021, 5:17pm UTC](https://forums.yoyoexpert.com/t/bearing-measurements/336836/3 "2021-04-07T17:17:10Z")

</div>

Okay, so if the width of a C spec bearing is 4.75mm, how can a yoyo gap be _wider_ than that?

---

<div class="post-metadata">

**Author:** ![Isaac](https://sea1.discourse-cdn.com/flex015/user_avatar/forums.yoyoexpert.com/isaac/32/597931_2.png) [@Isaac](https://forums.yoyoexpert.com/u/Isaac)\
**Post date:** [April 7, 2021, 5:21pm UTC](https://forums.yoyoexpert.com/t/bearing-measurements/336836/4 "2021-04-07T17:21:27Z")

</div>

Some sort of bearing seat shenanigans would be my guess.

---

<div class="post-metadata">

**Author:** ![zslane](https://sea1.discourse-cdn.com/flex015/user_avatar/forums.yoyoexpert.com/zslane/32/19816_2.png) [@zslane](https://forums.yoyoexpert.com/u/zslane)\
**Post date:** [April 7, 2021, 5:23pm UTC](https://forums.yoyoexpert.com/t/bearing-measurements/336836/5 "2021-04-07T17:23:52Z")

</div>

The bearing seat is a recessed groove that the bearing sits in, right? Since that groove always has a depth \> 0, that means the gap will always be _less_ than the full width of any bearing.

---

<div class="post-metadata">

**Author:** ![Rosenberg](https://sea1.discourse-cdn.com/flex015/user_avatar/forums.yoyoexpert.com/rosenberg/32/20465_2.png) [@Rosenberg](https://forums.yoyoexpert.com/u/Rosenberg)\
**Post date:** [April 7, 2021, 5:34pm UTC](https://forums.yoyoexpert.com/t/bearing-measurements/336836/6 "2021-04-07T17:34:28Z")

</div>

The bearing seat/ post is making contact with the inner bearing race when the yoyo is assembled. You could then machine the inner walls of the yoyo out to a width greater than the bearing width. Idk why you’d want to, but you could

---

<div class="post-metadata">

**Author:** ![zslane](https://sea1.discourse-cdn.com/flex015/user_avatar/forums.yoyoexpert.com/zslane/32/19816_2.png) [@zslane](https://forums.yoyoexpert.com/u/zslane)\
**Post date:** [April 7, 2021, 5:39pm UTC](https://forums.yoyoexpert.com/t/bearing-measurements/336836/7 "2021-04-07T17:39:18Z")

</div>

If the inner walls are machined _away_ from the bearing, wouldn’t that leave a tiny space between them? Wouldn’t you risk the string getting caught in that space during play?

---

<div class="post-metadata">

**Author:** ![Isaac](https://sea1.discourse-cdn.com/flex015/user_avatar/forums.yoyoexpert.com/isaac/32/597931_2.png) [@Isaac](https://forums.yoyoexpert.com/u/Isaac)\
**Post date:** [April 7, 2021, 5:41pm UTC](https://forums.yoyoexpert.com/t/bearing-measurements/336836/8 "2021-04-07T17:41:03Z")

</div>

That sounds kind of like the problem the Eetsit had:

> The string gap on the yo-yo was just a little too wide, causing the string to occasionally slip in between the bearing and the side of the yo-yo. This design flaw could be remedied by replacing the stock Baz Pads with thick Dif Pads. Some players had instead opted to sand down the bearing seat of their Eetsit yo-yos in order to correct this problem. The [Bapezilla](https://yoyo.fandom.com/wiki/Anti-Yo_Bapezilla) was later released as a follow up to the Eetsit, fixing the problematic string gap.

> **[Anti-Yo Eetsit](https://yoyo.fandom.com/wiki/Anti-Yo_Eetsit)**
>
> The Eetsit by Anti-Yo, released on February 14th, 2006, was the much-awaited successor to the Fluchs. Like its predecessor, the Eetsit has a machined aluminium body with a low-friction Slip Matte finish, but this time, it also has a large...

---

<div class="post-metadata">

**Author:** ![Rosenberg](https://sea1.discourse-cdn.com/flex015/user_avatar/forums.yoyoexpert.com/rosenberg/32/20465_2.png) [@Rosenberg](https://forums.yoyoexpert.com/u/Rosenberg)\
**Post date:** [April 7, 2021, 5:42pm UTC](https://forums.yoyoexpert.com/t/bearing-measurements/336836/9 "2021-04-07T17:42:26Z")

</div>

Yeah. I mean I’d imagine there’s some small amount wider that you can go that is still too small for a string to get lodged into but I’m sure there has to be a limit

---

<div class="post-metadata">

**Author:** ![zslane](https://sea1.discourse-cdn.com/flex015/user_avatar/forums.yoyoexpert.com/zslane/32/19816_2.png) [@zslane](https://forums.yoyoexpert.com/u/zslane)\
**Post date:** [April 7, 2021, 5:45pm UTC](https://forums.yoyoexpert.com/t/bearing-measurements/336836/10 "2021-04-07T17:45:23Z")

</div>

I guess. I mean, there are quite a number of yoyos with gap widths \> 4.75mm. The Replay Pro supposedly has a 4.80mm gap, and the Will has a 4.82mm gap. Hell, I’ve seen yoyos listed with a 5.00mm gap.

---

<div class="post-metadata">

**Author:** ![hobbygod](https://sea1.discourse-cdn.com/flex015/user_avatar/forums.yoyoexpert.com/hobbygod/32/120997_2.png) [@hobbygod](https://forums.yoyoexpert.com/u/hobbygod)\
**Post date:** [April 7, 2021, 5:52pm UTC](https://forums.yoyoexpert.com/t/bearing-measurements/336836/11 "2021-04-07T17:52:25Z")

</div>

The recessed groove is actually an air pocket. The actual seat is the part that kinda moves out from the axle hole slightly.

---

<div class="post-metadata">

**Author:** ![zslane](https://sea1.discourse-cdn.com/flex015/user_avatar/forums.yoyoexpert.com/zslane/32/19816_2.png) [@zslane](https://forums.yoyoexpert.com/u/zslane)\
**Post date:** [April 7, 2021, 5:56pm UTC](https://forums.yoyoexpert.com/t/bearing-measurements/336836/12 "2021-04-07T17:56:29Z")

</div>

Ah, okay, thank you for the clarification.

I’m asking about all this because I’m trying to understand the pros and cons of gap widths that are wider than the bearing.

---

<div class="post-metadata">

**Author:** ![hobbygod](https://sea1.discourse-cdn.com/flex015/user_avatar/forums.yoyoexpert.com/hobbygod/32/120997_2.png) [@hobbygod](https://forums.yoyoexpert.com/u/hobbygod)\
**Post date:** [April 7, 2021, 6:59pm UTC](https://forums.yoyoexpert.com/t/bearing-measurements/336836/13 "2021-04-07T18:59:04Z")

</div>

I’ll send a picture when I can to better explain it. Road tripping to PA atm.

---

<div class="post-metadata">

**Author:** ![MarkD](https://sea1.discourse-cdn.com/flex015/user_avatar/forums.yoyoexpert.com/markd/32/40845_2.png) [@MarkD](https://forums.yoyoexpert.com/u/MarkD)\
**Post date:** [April 7, 2021, 7:16pm UTC](https://forums.yoyoexpert.com/t/bearing-measurements/336836/14 "2021-04-07T19:16:51Z")

</div>

> [@zslane](#):
>
> Okay, so if the width of a C spec bearing is 4.75mm, how can a yoyo gap be _wider_ than that?

Many yoyo designs have a protruding ring at the inside of the response pad. This can be useful for:

1. Adding a tiny bit of centering for bearings that are flat
2. Expanding the gap (distance between the pads) beyond 3/16" without the string slipping past the bearing
3. Help keep the yoyo from snagging during wraps even when the gap is smaller

 ![image](https://us1.discourse-cdn.com/flex015/uploads/yoyoexpert1/original/4X/0/2/f/02f1f187581c8b1439ead21da4689c8b9c3f877b.png)

The bearing post is at the bottom, the two “moats” are the pad recess (top) and air gap (bottom)
